- RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT PDF
- RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT INSTALL
- RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT DRIVERS
- RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT UPDATE
RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT UPDATE
Is the latest Logitech software installed - there may be a firmware update available for your tranceiver which you won't get unless you have the Logitech software installed. You're getting this problem when using the Logitech mouse in the USB 3.0 port but what about whether other devices cause such problems? Was the missing step 12 one where you tested the USB 3.0 port with another device eg the Pendrive tranferring files or formatting etc for 1/4 of an hour or so to see if you could generate the same problem? I'm trying to determine if I need to RMA this board. Has anyone else experienced this issue? Maybe I have a bad USB 3.0 Controller on the board?Īdvice, rants, raves, words of encouragement all welcome. That will do two things:ġ.) return everything to it's "out of the box" condition, andĢ.) verify if the reason I didn't see it happen when I originally setup the system was because I didn't use the system in that state long enough for the USB 3.0 ports to stop working.
RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT DRIVERS
The only thing left for me to try is to downgrade to Version 1900 (the BIOS as shipped) and reinstall Windows 7 and the appropriate drivers from the Intel Driver DVD shipped with the motherboard. Still it makes trouble shooting a little tough because until it randomly happens, I don't know if I found "root cause" and fixed it. Unfortunately, the problem occurs randomly, but generally within about a ½ hour of use. USB 3.0 ports appear to be dead but continue to show up in Device Manager as "working properly." RESULT: The mouse cursor freezes after a period of time and thumb drives are not recognized. For this install, I again used the drivers on the DVD shipped with the system.
RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT INSTALL
At this point, I thought it may be a BIOS issue so I decided to downgrade from Version 2040 to Version 2023 and do a clean install of Windows 7. RESULT: Mouse cursor freezes again after a short period of time - 5 to maybe 10 minutes.ġ3. I reboot for good measure and continue working. I update the drivers for the USB 3.0 Controller from Version 2.0.20.0 to Version 2.1.19.0 (the latest available from Intel). RESULT: and short time later same thing – mouse cursor is frozen.ġ1.
RESULT: The USB 3.0 ports are "alive" again. In Device Manager, I Disable then Enable the Renesas Electronics USB 3.0 Host Controller RESULT: Device Manager shows that both the Renesas Electronics USB 3.0 Host Controller and Root Hub are working properly.ĩ. I plug in a USB Thumb Drive to the other USB 3.0 port.
RESULT: About 5 minutes later the mouse cursor freezes again.ħ. Mouse operational and thumb drive recognized. RESULT: Both USB 3.0 ports seem to be working again. RESULT: The system doesn't recognize that a thumb drive has been plugged in. I plug a USB thumb drive into the USB 3.0 port. I plug the mouse receiver back into the USB 3.0 port.Ĥ. I unplug the mouse receiver from the USB 3.0 port and plug it into a USB 2.0 port.ģ. I unplug the mouse receiver from the USB 3.0 port and plug it back in.Ģ.
RENESAS USB 3.0 DRIVER DISABLE POWER MANAGEMENT PDF
I start using the system, reading PDF files, surfing the Intel forums (maybe for 15 minutes or so) when my mouse cursor freezes (NOT the system, just the mouse). Yup, I ran into the whole video card fiasco but thanks to another thread on this site, I successfully downgraded to Version 2040.Īt this point, I think I'm back on track. I foolishly decided to update my BIOS from Ver.
The mouse appeared to be working fine, although I didn't use it very much before. Since I don't currently have any USB 3.0 devices, I decided to use one of the USB 3.0 ports for the receiver to my Logitech V450 Nano wireless mouse (a USB 2.0 device). I used the Intel Driver Disk that came with the board to install the needed drivers. I installed Windows 7 Ultimate 64bit (w/ SP1 and all updates).
I have a new build (Labor Day Weekend 2011):